Understanding the technical specifications and safety guidelines for your 3D printing filament is essential for achieving optimal print results and ensuring a safe working environment. This documentation hub provides access to Technical Datasheets (TDS) and Material Safety Data Sheets (MSDS/SDS) for all DREMC filament ranges. Whether you're fine-tuning print parameters, checking material properties, or reviewing safety handling instructions, you'll find the critical information you need right here. Where applicable all basic filaments are Compliance with ROHS / REACH, you can find full applicable materials composition within SDS.
TABLE OF CONTENTS
The typical values presented in this data sheet are intended for reference and comparison purposes only among DREMC range. They should not be used for design specifications or quality control purposes. Actual values may vary significantly with printing conditions. End- use performance of printed parts depends not only on materials, but also on part design, environmental conditions, printing conditions. Product specifications may be subject to changes between manufacturing batch.
Each user is responsible for determining the safety, lawfulness, technical suitability, and disposal/ recycling practices of DREMC materials for the intended application. DREMC makes no warranty of any kind, unless announced separately, to the fitness for any use or application. DREMC shall not be made liable for any damage, injury or loss induced from the use of DREMC materials in any application.
Print Profiles: https://support.dremc.com.au/en/support/solutions/articles/51000343310-dremc-filament-3d-printing-profile
Feeling overwhelm with material choice? Do you need recommendation what is best suit materials for your next project/product? Contact Us! https://support.dremc.com.au/support/tickets/new
TDS (Technical Data Sheet):
PLA
TPU
PEBA TDS
TPU Aero TDS
TPU 64D TDS
TPU 85A TDS
TPU 72D TDS
PETG
PET
ABS / ASA
PC
Nylon
Other
Filament Cleaning [No TDS available]
SDS (Safety Data Sheet):
PLA
PLA Matte / PLA Sparkle / PLA Silk SDS
TPU
PEBA SDS
TPU Aero SDS
TPU 64D SDS
TPU 85A SDS
TPU 72D SDS
PETG
PETG GF SDS
PCTG SDS
PET
ABS/ASA
PC
PC ABS FR SDS
Nylon
Other
PVA SDS
Filament Cleaning SDS
PC PBT GF TDS
Compliance with ROHS / REACH
To the best of our knowledge, the above-mentioned products of DREMC™ do not intentionally contain any substances currently listed on the Candidate List of Substances of Very High Concern (SVHC) published by the European Chemicals Agency (ECHA) at https://echa.europa.eu/candidatelist-table, nor any substances subject to authorization (Annex XIV) or restriction (Annex XVII) under Regulation (EC) No 1907/2006 (REACH) and its subsequent amendments.
These substances are therefore not expected to be present above applicable limit values. The possible presence of analytically detectable traces, potentially introduced via raw materials, auxiliaries, or additives, cannot be excluded. Specific analyses to measure such traces have not beenper formed on raw materials or final products.
To the best of our knowledge, the above-mentioned products of DREMC™ do not intentionally contain the substances listed below. Therefore, these substances are not expected to be present above applicable limit values. However, the presence of analytically detectable traces—possibly introduced via raw materials, auxiliaries, and additives—cannot be excluded. Specific analyses to measure such traces have not been performed on raw materials or final products.
List of substances:
Cadmium
Lead
Mercury
Hexavalent chromium
Flame retardants PBB and PBDE, including:
Pentabromodiphenyl ether (CAS No. 32534-81-9)
Octabromodiphenyl ether (CAS No. 32536-52-0)
Decabromodiphenyl ether (CAS No. 1163-19-5)
Bis(2-ethylhexyl) phthalate (DEHP)
Butyl benzyl phthalate (BBP)
Dibutyl phthalate (DBP)
Diisobutyl phthalate (DIBP)
Was this article helpful?
That’s Great!
Thank you for your feedback
Sorry! We couldn't be helpful
Thank you for your feedback
Feedback sent
We appreciate your effort and will try to fix the article